A step-by-step guide to installing Plytech’s QuickTrim Rubber Roof Trims

When installing QuickTrim (a flat roof edge trim), choosing the right product can make a significant difference in both efficiency and longevity.

Plytech’s QuickTrim is an innovative system designed to simplify the installation of rubber roof trims, offering a lightweight, durable, and easy-to-fit solution that ensures a professional finish every time. Unlike other rubber roofing trims, QuickTrim features pre-cut sections, secure interlocking mechanisms, and built-in drainage solutions to enhance both performance and appearance.

This guide will walk you through the installation process, covering the tools and materials required, how to cut and fit QuickTrim, common mistakes to avoid, and why Plytech’s QuickTrim is the superior choice for your roofing project.

Tools and materials needed

Before you begin, ensure you have all the necessary tools and materials to complete the installation efficiently:

Plytech’s QuickTrim flat roof edge trim system
Tape measure
Chalk line or marker
Handsaw or angle grinder
Drill with appropriate drill bits
Fixing screws or nails
Sealant or adhesive (if required)
Rubber roofing membrane
PPE (gloves, safety glasses)

Having all materials and tools prepared in advance will streamline the installation process and help achieve a professional finish.

How to cut, fit, and secure Plytech’s QuickTrim

Step 1

Measure and mark

Start by measuring the perimeter of your flat roof where the rubber roof trims will be installed. Use a chalk line or marker to indicate where each section of Plytech’s QuickTrim will be placed. Ensure measurements are accurate to avoid gaps or overlapping sections.

Step 2

Cutting the trims

One of the major advantages of QuickTrim is that it comes in pre-cut sections, reducing the amount of cutting required. However, if adjustments are needed, use a handsaw or angle grinder to trim pieces to the required lengths. For corners, create mitre cuts for a seamless fit. Always double-check measurements before cutting to prevent material wastage.

Step 3

Position the trim

Lay the cut pieces along the marked lines to confirm a proper fit. Adjust as necessary before securing them in place. QuickTrim’s interlocking design ensures sections connect smoothly, eliminating gaps and improving overall aesthetics.

Step 4

Fixing the trim in place

Secure the QuickTrim using screws or nails at evenly spaced intervals, typically every 300-500mm. The design of Plytech’s QuickTrim makes fixing simpler, as it includes pre-drilled holes for precise placement. Ensure each fixing is properly tightened without over-tightening to prevent damage.

Step 5

Sealing the joints

Unlike traditional flat roof edge trims, QuickTrim features a built-in drainage system, reducing the need for excessive sealing. However, where necessary, apply a suitable sealant or adhesive at the joints to ensure additional weatherproofing.

Step 6

Final checks

Inspect the installation for any loose sections, misalignments, or gaps. With Plytech’s QuickTrim, adjustments are minimal due to the precise, modular design that ensures a professional finish with minimal effort.

Common mistakes to avoid

Even with an advanced system like Plytech’s QuickTrim, errors can still occur. Here are some common mistakes to watch out for:

Inaccurate measurements
Always double-check measurements before cutting to ensure a precise fit.

Improper fixing
Over-tightening screws can crack or distort the trim, while under-tightening can lead to instability.

Ignoring sealant application
Skipping the sealing process where needed can lead to water ingress and long-term damage.

Poor alignment
Misaligned trims affect both appearance and functionality, QuickTrim’s interlocking system helps prevent this issue.

Not allowing for expansion and contraction
Some materials expand and contract with temperature changes, so consider this when fitting trims.

Why Plytech’s QuickTrim is the best choice

Other rubber roof trims often require excessive cutting, sealing, and aligning, making the installation process time-consuming. Plytech’s QuickTrim eliminates these challenges with:

Pre-cut lengths and easy-to-fit sections, reducing on-site cutting time
Secure interlocking mechanisms that ensure a watertight and professional finish
Lightweight yet durable materials, making handling and installation simpler
Built-in drainage solutions, helping to direct water off the roof efficiently
Pre-drilled fixing points, reducing errors and improving installation speed
Drip Edge Trim, perfect for gutter-edge flat roofing, ensuring efficient water management
Check Kerb System, a raised-edge solution designed to prevent water overflow

By choosing Plytech’s QuickTrim, both professionals and DIY installers can achieve a high-quality, low-maintenance, and weatherproof finish with minimal effort.

Properly installing flat roof edge trims is essential to ensuring the longevity and performance of your roofing system. Plytech’s QuickTrim simplifies the process by offering a high-quality, easy-to-install alternative that saves time, reduces errors, and ensures a superior finish.

For more training information visit our EPDM Training Centre